- #FOSS VISCOSITY METER MANUAL#
- #FOSS VISCOSITY METER UPGRADE#
- #FOSS VISCOSITY METER SOFTWARE#
- #FOSS VISCOSITY METER CODE#
For each cell containing “-“, viscosity ranges are not applicable due to historical reasons. Viscosity ranges are shown in or, respectively. viscosity are calculated values for RH standard speeds (0.5 rpm to 100 rpm) viscosity are calculated values for L standard speeds (0.3 rpm to 60 rpm) The following tables give you an overview of the theoretical (calculated) viscosity range per measuring system. Hence, samples with a viscosity around 1 mPa.s (like water) can be measured with DG26 or UL26 and ViscoQC 100/300-L.Ī.3.3 Viscosity ranges per measuring system/spindle and torque model The largest surface area is provided by the double-gap and the ultra-low viscosity adapter system.Surface area decreases from CC26 to CC12.General rule of thumb for measuring systems: The lower the viscosity, the larger the surface area. If sample volume is limited ( <20 mL), an absolute measuring system (cylinder, double-gap, small sample adapter, ultra-low viscosity adapter), or a small vane spindle (V74, V75) is required. If large sample volumes (~500 mL) are available, both relative measuring systems (L1-L4 spindle, RH1-RH7 spindle, vane spindles V71-V75, T-Bar spindles), or absolute measuring systems (concentric cylinder, double-gap, small sample adapter, ultra-low viscosity adapter) can be used. It depends on the available sample volume and viscosity of the sample. A.3 Which spindle/measuring system should I choose?
#FOSS VISCOSITY METER MANUAL#
** Manual input of reference density possible, no density measurement available. 200 BU for ViscoQC 100/300 – H (depending on measuring system) Typical samples: pastes, mayonnaise, peanut butter, ointmentsĪ.2 What information is displayed on ViscoQC? ViscoQC 100/300 - H for high-viscosity samples.Typical samples: paints, dairy products, shampoo, lotion ViscoQC 100/300 - R for medium-viscosity samples.Typical samples: solvents, oils, juices, mouthwash ViscoQC 100/300 - L for low-viscosity samples.*** With optional PTD 100 Cone-Plate, with RH1 spindle 800 mPa.sĪ.1 Which model should I choose for my sample? ** With optional PTD 100 Cone-Plate, with RH1 spindle 100 mPa.s * With optional PTD 100 Cone-Plate, with L1 spindle 15 mPa.s
#FOSS VISCOSITY METER CODE#
Options: keyboard, mouse, 2D bar code readerĮN, DE, ES, FR, IT, PT, JA, KO, RU, ZH-CN, ZH-TW, PO, CZEĮasiest spindle exchange (magnetic coupling)Īutomatic spindle recognition (Toolmaster™)Īutomatic speed searching function (TruMode™) 60 ☌ to +300 ☌ (temperature sensing with optional Pt100) V-Comply delivers compliance to 21 CFR Part 11 (e.g., audit trail, electronic signature), including qualification documentationįor automated sample name input, a bar code reader is available for ViscoQC 300.įreely selectable speeds within the speed rangeĪmbient to +100 ☌ (control of L/RH spindles with optional thermostat bath).V-Curve adds real-time graphs, analysis (e.g., yield point), programmability, and extended method functionality (e.g., with PTD 175).
#FOSS VISCOSITY METER SOFTWARE#
Further software functionality can be added to ViscoQC 300 with up to two optionally upgradeable software modules: V-Curve and/or V-Comply. For very small sample volumes (0.5 mL to 2 mL), PTD 100 Cone-Plate is the accessory of choice. heating/cooling rate 5.2/6.3 K/min) and have less than 20 mL of sample volume, simply use the Peltier temperature device PTD 80. If you need super-fast and accurate sample temperature control (max.
Gel time/pot life determination of adhesives is automatically possible with both models.
#FOSS VISCOSITY METER UPGRADE#
To measure new paste-like formulations (e.g., wall putty), you can upgrade your instruments with the Heli-Plus and T-bar spindles. ViscoQC 100 and ViscoQC 300 are future-proof: They grow with your evolving needs.
0 kommentar(er)
